FIIG A003B ITEM CHARACTERISTICS DATA REQUIREMENTS

SECTION I

ITEM CHARACTERISTICS DATA REQUIREMENTS

Applicability Key SB

App Key	MRC	Mode Code	Requirements

ALL
	NAME	D	ITEM NAME
	Definition: A NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
	Reply Instructions: Enter the applicable Item Name Code appearing in the Index of Approved Item Names. (e.g., NAMED06672*)


	NOTES FOR MRCS THSD AND CRGF:
	1. FOR APPLICABILITY KEY BK, REPLY TO MRCS THSD AND CRGF.
	2. FOR APPLICABILITY KEY BN, REPLY TO THE BOLT END EXTERNAL THREAD.
BA, BB, BC, BD, BE, BF, BG, BH, BJ, BK, BL, BM, BN, BP, BR, BS, BT, BU, BV, BW, BX, BY, BZ, CA, CB, CC, CD, CE, CF, CH, SA, SB, SC, SE, SG, SJ, SK, SL, SQ, SR, SS, SU, TA, TB, TC, TD, TE*
	THSD	D	THREAD SERIES DESIGNATOR
	Definition: A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
	Reply Instructions: Enter the applicable Reply Code from Appendix A, Table 1 . (e.g., THSDDNC*)


	NOTE FOR MRCS AHYM, CMLP, CQQR, AAJD, CQWR, AND CFSG:
	1. SEE Appendix A, Table 1 . A REPLY MUST BE ENTERED FOR THE MRCS FOLLOWING THE REPLY CODE.
	2. FOR APPLICABILITY KEY SG, SEE APPENDIX C, TABLE 3 FOR CONVERSION OF NUMBER SIZE TO DECIMAL EQUIVALENTS.
BA, BB, BC, BD, BE, BF, BG, BH, BJ, BK, BL, BM, BN, BP, BR, BS, BT, BU, BV, BW, BX, BY, BZ, CA, CB, CC, CD, CE, CF, CH, SA, SB, SC, SE, SG, SJ, SK, SL, SQ, SR, SS, SU, TA, TB, TC, TD, TE* (See Note Above)
	AHYM	J	NOMINAL THREAD DIAMETER
	Definition: THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION, AND TERMINATES AT THE CIRCUMFERENCE.
	Reply Instructions: Enter the applicable Reply Code from the table below, followed by the numeric value. (e.g., AHYMJA0.250; AHYMJL6.0)

REPLY CODE	REPLY (AA05)
A	INCHES
L	MILLIMETERS

	NOTE FOR MRCS CMLP, CQQR, AAJD, CQWR AND CFSG: FOR APPLICABILITY KEY SJ ONLY A REPLY IS NOT REQUIRED FOR THESE MRCS.
BA, BB, BC, BD, BE, BF, BG, BH, BJ, BK, BL, BM, BN, BP, BR, BS, BT, BU, BV, BW, BX, BY, BZ, CA, CB, CC, CD, CE, CF, CH, SA, SB, SC, SE, SG, SJ, SK, SL, SQ, SR, SS, SU, TA, TB, TC, TD, TE* (See Note Above and Preceding MRC AHYM)
	CMLP	A	THREAD QUANTITY PER INCH
	Definition: THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
	Reply Instructions: Enter the quantity.
	(e.g., CMLPA16*;
	CMLPA4-1/2*)


BA, BB, BC, BD, BE, BF, BG, BH, BJ, BK, BL, BM, BN, BP, BR, BS, BT, BU, BV, BW, BX, BY, BZ, CA, CB, CC, CD, CE, CF, CH, SA, SB, SC, SE, SG, SJ, SK, SL, SQ, SR, SS, SU, TA, TB, TC, TD, TE*(See Note Preceding MRCS CMLP and AHYM)
	CQQR	B	THREAD PITCH IN MILLIMETERS
	Definition: A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS, EXPRESSED IN MILLIMETERS.
	Reply Instructions: Enter the numeric value. (e.g., CQQRB1.0*)


	NOTE FOR MRC AAJD: WHEN THE SOURCE DOCUMENT SPECIFIES A MAXIMUM AND MINIMUM PITCH DIAMETER IDENTICAL TO OR WITHIN THE LIMITS OF A STANDARD CLASS OF THREAD, REPLY WITH THE STANDARD CLASS OF THREAD. ALL CLASS OF FITS SHOULD BE REFLECTED BY THE SIMILAR CLASS OF THREAD. (i.e., CLASS 1 FIT AS 1A THREAD CLASS)
BA, BB, BC, BD, BE, BF, BG, BH, BJ, BK, BL, BM, BN, BP, BR, BS, BT, BU, BV, BW, BX, BY, BZ, CA, CB, CC, CD, CE, CF, CH, SA, SB, SC, SE, SG, SJ, SK, SL, SQ, SR, SS, SU, TA, TB, TC, TD, TE* (See Note Above and Preceding MRC AHYM and CMLP)
	AAJD	A	THREAD CLASS
	Definition: A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
	Reply Instructions: Enter the thread class. (e.g., AAJDA1A; AAJDAMEDIUM)


	NOTE FOR MRC CQWR: METRIC EXTERNAL THREADS AND DEVIATIONS ARE ALWAYS INDICATED BY LOWER CASE LETTERS e,g OR h, BUT ARE INPUT IN UPPER CASE. WHEN THE PITCH AND MAJOR DIAMETER TOLERANCES ARE EQUAL (IDENTICAL) (i.e., M6x1-6h6h OR M6x1-6h), ENTER THE DESIGNATION ONCE.
	WHEN THE PITCH AND MAJOR DIAMETER TOLERANCE ARE UNEQUAL (NON-IDENTICAL) (i.e., M6x1-4h6h), ENTER THE DESIGNATION FOR BOTH.
BA, BB, BC, BD, BE, BF, BG, BH, BJ, BK, BL, BM, BN, BP, BR, BS, BT, BU, BV, BW, BX, BY, BZ, CA, CB, CC, CD, CE, CF, CH, SA, SB, SC, SE, SG, SJ, SK, SL, SQ, SR, SS, SU, TA, TB, TC, TD, TE* (See Note Above and Preceding MRC AHYM and CMLP)
	CQWR	A	EXTERNAL THREAD TOLERANCE CLASS
	Definition: A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITIONS AND GRADES OF AN EXTERNAL THREAD.
	Reply Instructions: Enter the designator. (e.g., CQWRA6H; CQWRA4H6H)


BA, BB, BC, BD, BE, BF, BG, BH, BJ, BK, BL, BM, BN, BP, BR, BS, BT, BU, BV, BW, BX, BY, BZ, CA, CB, CC, CD, CE, CF, CH, SA, SB, SC, SE, SG, SJ, SK, SL, SQ, SR, SS, SU, TA, TB, TC, TD, TE* (See Note Preceding MRC AHYM and CMLP)
	CFSG	J	NONSTANDARD THREAD PITCH DIAMETER
	Definition: THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A NONSTANDARD STRAIGHT SCREW THREAD.
	Reply Instructions: Enter the applicable Reply Code from the table below, followed by the numeric values separated by a slash. Precede all values with a P. (e.g., CFSGJAP0.2157/P0.2195; CFSGJLP5.4/P5.5)

REPLY CODE	REPLY (AA05)
A	INCHES
L	MILLIMETERS

	NOTE FOR MRC AAJF: DO NOT REPLY TO THIS REQUIREMENT FOR THE WOOD SCREW END OF THE APPL KEY BK. FOR APPLICABILITY KEY BN, REPLY TO THE BOLT END EXTERNAL THREAD.
BA, BB, BC, BD, BE, BF, BG, BH, BJ, BK, BL, BM, BN, BP, BR, BS, BT, BU, BV, BW, BX, BY, BZ, CA, CB, CC, CD, CE, CF, CH, SA, SB, SC, SE, SG, SK, SL, SQ, SR, SS, SU, TA, TB, TC, TD, TE* (See Note Above)
	AAJF	D	THREAD DIRECTION
	Definition: THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
	Reply Instructions: Enter the applicable Reply Code from the table below. (e.g., AAJFDAAL*)

REPLY CODE	REPLY (AA38)
AAG	LEFT-HAND
AAL	RIGHT-HAND

	NOTE FOR MRC AASA:
	1. FOR COUNTERSUNK ITEMS THAT ARE FULLY THREADED, SUBTRACT THE HEAD HEIGHT FROM THE FASTENER LENGTH TO COMPUTE THREAD LENGTH.
	2. ITEMS THREADED AS CLOSE TO THE HEAD AS POSSIBLE CONSTITUTES A FULLY THREADED ITEM.
	3. FOR APPLICABILITY KEY BK - ENTER REPLY FOR MACHINE SCREW END ONLY.
BA, BB, BC, BD, BF, BG, BH, BK, BL, BM, BN, BP, BR, BS, BT, BU, BV, BW, BX, BY, BZ, CA, CB, CC, CE, CF, CH, SA, SB, SC, SE, SG, SJ, SK, SL, SQ, SR, SS, SU*, TB, TC, TD (See Note Above)
	AASA	J	THREAD LENGTH
	Definition: A MEASUREMENT OF THE EXTENT OF THREADS, INCLUDING INCOMPLETE THREADS, ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
	Reply Instructions: Enter the applicable Reply Codes from Tables 1 and 2 below, followed by the numeric value. (e.g., AASAJAA0.250; AASAJLA6.0; AASAJAB0.312$$JAC0.328*)

Table 1
REPLY CODE	REPLY (AA05)
A	INCHES
L	MILLIMETERS

Table 2
REPLY CODE	REPLY (AC20)
A	NOMINAL
B	MINIMUM
C	MAXIMUM

	NOTE FOR MRC AASB: FASTENER LENGTH IS INDICATED BY LEGEND L IN Appendix B, REFERENCE DRAWING GROUP C . BOLT, HANGER AND SETSCREWS WITHOUT A HEAD ARE MEASURED OVERALL.
BA, BB, BC, BD, BE, BF, BH, BJ, BK, BM, BN, BP, BQ, BR, BS, BT, BU, BW, BX, BY, BZ, CA, CB, CC, CF, CG*, CH, SA, SB, SC, SD, SE, SG, SJ, SK, SL, SM, SN, SP, SQ, SR, SS, SU, TB, TC, TD, TE (See Note Above)
	AASB	J	FASTENER LENGTH
	Definition: THE DIMENSION, MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS, FROM THE LARGEST BEARING SURFACE OF THE FASTENER HEAD TO THE EXTREME OPPOSITE END, OR AS SPECIFICALLY DESIGNATED FOR OTHER TYPE FASTENERS.
	Reply Instructions: Enter the applicable Reply Codes from Tables 1 and 2 below, followed by the numeric value. (e.g., AASBJAA0.750; AASBJLA19.1; AASBJAB0.750$$JAC0.760*)

Table 1
REPLY CODE	REPLY (AA05)
A	INCHES
L	MILLIMETERS

Table 2
REPLY CODE	REPLY (AC20)
A	NOMINAL
B	MINIMUM
C	MAXIMUM

	NOTE FOR MRCS MATT, MDCL, SFTT AND STDC:
	1. SEE APPENDIX C, TABLE 7 FOR CLARIFICATION OF TERMS AND RECORDING INSTRUCTIONS.
	2. FOR APPLICABILITY KEYS BA, SA, AND SU - THE BOLT/SCREW COMPONENT WILL BE CLASSIFIED AS FASTENER.
ALL (See Note Above)
	MATT	D	MATERIAL
	Definition: THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code and applicable Reply Code from Appendix A, Table 6 . (e.g., MATT2AADALB000; MATT2AADGSB000$$DPCAM00; MATT2AADALB000$DSTA000*)


ALL* (See Note Preceding MRC MATT)
	MDCL	J	MATERIAL DOCUMENT AND CLASSIFICATION
	Definition: THE SPECIFICATION, STANDARD, OR MANUFACTURERS REFERENCE, AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code and the applicable Reply Code from Appendix A, Table 3 and Appendix A, Table 4 , and the document designation and classification.
	(e.g., MDCL2AAJBAQQ-A-250/5,T4*;
	MDCL2AAJFBGL2345, CAGE94117$$JBCL-P-410*;
	MDCL2AAJGBAMS4022$JDCMIL-S-11415*)


ALL*
	CWJT#	J	OFFSET YIELD STRENGTH
	Definition: THE MAXIMUM LOAD WHICH CAN BE APPLIED TO THE MATERIAL IN LONGITUDINAL DIRECTION PER CROSS-SECTIONAL UNIT WITH A REMAINING PERMANENT ELONGATION OF 0.2 PERCENT OF THE MEASURED LENGTH.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code and the applicable Reply Code from the table below and the numeric value. (e.g., CWJT2AAJS640.0; CWJT2AHJV900.0)

REPLY CODE	REPLY(AB18)
S	MEGAPASCALS
R	NEWTONS PER SQUARE MILLIMETER
V	POUNDS PER SQUARE INCH

ALL* (See Note Preceding MRC MATT)
	SFTT	D	SURFACE TREATMENT
	Definition: THE METALLIC, NONMETALLIC, AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED, DIPPED, AND/OR COATED. THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code and the applicable Reply Code from Appendix A, Table 7 . (e.g., SFTT2AADANA000; SFTT2AADANA000$$DCMA000; SFTT2AADCDA000$DZNA000*)


ALL* (See Note Preceding MRC MATT)
	STDC	J	SURFACE TREATMENT DOCUMENT AND CLASSIFICATION
	Definition: THE SPECIFICATION, STANDARD, OR MANUFACTURERS REFERENCE, AND THE CLASSIFICATION DESIGNATION, SUCH AS TYPE, CLASS, GRADE, AND THE LIKE, THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code and the applicable Reply Code from Appendix A, Table 3 and Appendix A, Table 5 , followed by the document designation and classification.
	(e.g., STDC2AAJDAMIL-A-8625*;
	STDC2AAJGBAMS2470$$JFC951034, CAGE05257*;
	STDC2AAJBBQQ-P-416, TY2CL2$JBCQQ-Z-325*)


ALL*
	HUES	D	COLOR
	Definition: A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE, DOMINANT WAVELENGTH, AND PURITY.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code and the applicable Reply Code from Appendix A, Table 8 . (e.g., HUES2BFDBL0000; HUES2XADGR0000$$DRE0000; HUES2XADBL0000$DBU0000*)


	NOTE FOR MRC CQFM: TO ASSURE CONSISTENCY IN REPLIES, THE FOLLOWING RULES SHALL BE FOLLOWED: IF NO HARDNESS FOR THE ITEM OF SUPPLY IS LISTED IN THE SPECIFICATION AND/OR STANDARD, BUT THE PROCUREMENT DOCUMENT REFERENCED THEREON CITES A HARDNESS RATING FOR THE FINISHED ITEM OF SUPPLY, THIS RATING SHALL BE RECORDED IN REPLY TO MRC CQFM.
	WHEN THE MATERIAL SPECIFICATION LISTS A HARDNESS RATING FOR THE MATERIAL FROM WHICH THE ITEM IS FABRICATED, THIS RATING SHALL NOT BE RECORDED AS A REPLY TO MRC CQFM SINCE THERE IS FREQUENTLY A MODIFICATION DURING FABRICATION.
ALL* (See Note Above)
	CQFM	J	HARDNESS RATING
	Definition: A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF AN ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code, the applicable Reply Codes from Appendix A, Table 9 , the table below, and the numeric value. (e.g., CQFM2XAJRCA40.0; CQFM2BFJRCB45.0$$JRCC55.0)

REPLY CODE	REPLY (AC20)
A	NOMINAL
B	MINIMUM
C	MAXIMUM

	NOTE FOR MRCS CQBC AND CQHQ: TO ASSURE CONSISTENCY IN REPLIES, THE FOLLOWING RULES WILL BE FOLLOWED:
	IF NO TENSILE OR YIELD STRENGTH RATING FOR THE ITEM OF SUPPLY IS LISTED IN THE SPECIFICATION AND/OR STANDARD, BUT THE PROCUREMENT DOCUMENT REFERENCED THEREON CITES A TENSILE OR YIELD STRENGTH RATING FOR THE FINISHED ITEM OF SUPPLY, THIS RATING SHALL BE RECORDED IN REPLY TO MRC CQBC OR CQHQ RESPECTIVELY.
	WHEN THE SPECIFICATION AND/OR STANDARD ONLY CONTAIN TABLES WHICH LIST THE ULTIMATE TENSILE OR YIELD STRENGTH FOR THE DIFFERENT SIZES, THE DATA ON THESE TABLES SHALL NOT BE USED FOR TENSILE OR YIELD STRENGTH.
	WHEN THE SPECIFICATION AND/OR STANDARD LISTS A TENSILE OR YIELD STRENGTH RATING FOR THE MATERIAL FROM WHICH THE ITEM IS FABRICATED, THIS MATERIAL RATING SHALL NOT BE USED AS A REPLY TO THE TENSILE OR YIELD STRENGTH SINCE THERE IS FREQUENTLY A MODIFICATION DURING FABRICATION.
BA, BB, BC, BD, BE, BF, BG, BH, BJ, BK, BL, BM, BN, BP, BQ, BR, BS, BT, BU, BV, BW, BX, BY, BZ, CA, CB, CC, CD, CE, CF, CG, CH, SA, SB, SC, SD, SE, SF, SG, SJ, SK, SL, SM, SN, SP, SQ, SR, SS, ST, SU, TA, TB, TC, TD, TE (See Note Above)
	CQBC	J	MINIMUM TENSILE STRENGTH
	Definition: THE MAXIMUM RATED LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION, PER UNIT OF CROSS-SECTIONAL AREA, THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
	Reply Instructions: Enter the applicable Reply Code from the table below, followed by the numeric value. (e.g., CQBCJP160000; CQBCJS1100)

REPLY CODE	REPLY (AN71)
S	MEGAPASCALS
Z	NEWTONS PER SQUARE MILLIMETER
P	POUNDS PER SQUARE INCH

ALL* (See Note Preceding MRC CQBC)
	CQHQ	J	MINIMUM YIELD STRENGTH
	Definition: THE STRESS AT WHICH A MATERIAL EXHIBITS A SPECIFIED LIMITING DEVIATION FROM THE PROPORTIONALITY OF STRESS OR STRAIN.
	Reply Instructions: Enter the applicable Reply Code from the table below, followed by the numeric value. (e.g., CQHQJP160000; CQHQJS1100)

REPLY CODE	REPLY (AN71)
S	MEGAPASCALS
P	POUNDS PER SQUARE INCH

BB, BX, SA, SB, SC, SE, SK #, SL, SS, TB, TC
	AAWU	J	SINGLE SHEAR STRENGTH
	Definition: THE MINIMUM LOAD, APPLIED PREPENDICULARLY TO THE LONGITUDINAL AXIS OF AN ITEM, AT WHICH POINT THE ITEM WILL FRACTURE WHEN SUBJECTED TO THE STANDARD SINGLE SHEAR TEST METHOD.
	Reply Instructions: Enter the applicable Reply Code from the table below, followed by the numeric value. (e.g., AAWUJV291500; AAWUJS2009)

REPLY CODE	REPLY (AB18)
S	MEGAPASCALS
V	POUNDS PER SQUARE INCH

	NOTE FOR MRC AASK: FOR APPLICABILITY KEY CG - IF STYLE 79 WAS ENTERED FOR MRC STYL, A RESPONSE MUST BE GIVEN TO MRC AASK.
BA, BB, BC, BD, BE, BF, BH, BJ, BM, BN, BP, BQ, BR, BS, BT, BU, BW, BX, BY, BZ, CA, CB, CC, CF, CG, CH, SA, SB, SC, SD, SE, SG, SJ, SK, SL, SM, SN, SP, SQ, SR, SS, SU, TB, TC, TD, TE (See Note Above)
	AASK	L	HEAD STYLE
	Definition: THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HEAD.
	Reply Instructions: Enter the group designator and the applicable style number from Appendix B, Reference Drawing Group C . (e.g., AASKLC1*)

BC, BF, BM, BR, BW #, BX, BY, SB, SC, SE, SK #, SL, SQ, SS
	AAUM	D	LOCKING FEATURE
	Definition: AN ELEMENT INSERTED INTO THE FASTENER, OR A DESIGN FEATURE, THAT ENABLES THE FASTENER TO EFFECTIVELY RESIST VIBRATION AND ROTATION.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code and the applicable Reply Code from Appendix A, Table 10 . (e.g., AAUM2BFDEA; AAUM2AZDDK$DDL; AAUM2AZDDW; AAUM2BFDDL)


BA, BC, BF, BM, BN, BR, BW* #, BX, BY, CG, SA, SB, SC, SE, SK #, SL, SQ, SR, SS, TB, TC
	CRHC	L	HOLE CONFIGURATION STYLE
	Definition: THE STYLE DESIGNATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HOLE CONFIGURATION.
	Reply Instructions: Enter the group designator and the applicable style number from Appendix B, Reference Drawing Group E . (e.g., CRHCLE4*)


	NOTE FOR MRCS BQDM AND ASXK: IF A REPLY IS ENTERED FOR MRC CRHC, REPLY TO MRCS BQDM AND ASXK.
BA, BC, BF, BM, BN, BR, BW* #, BX, BY, CG, SA, SB, SC, SE, SK #, SL, SQ, SR, SS, TB, TC (See Note Above)
	BQDM	D	HOLE TYPE
	Definition: INDICATES THE TYPE OF HOLE(S) PROVIDED IN THE ITEM.
	Reply Instructions: Enter the applicable Reply Code from the table below. (e.g., BQDMDAG; BQDMDAG$$DAX; BQDMDAG$DAX*)

REPLY CODE	REPLY (AH37)
AG	DRILLED
AX	THREADED

BA, BC, BF, BM, BN, BR, BW* #, BX, BY, CG, SA, SB, SC, SE, SK #, SL, SQ, SR, SS, TB, TC (See Note Preceding MRC BQDM)
	ASXK	A	HOLE QUANTITY
	Definition: THE NUMBER OF HOLES PROVIDED.
	Reply Instructions: Enter the quantity. (e.g., ASXKA4; ASXKA2$$A3)


	NOTE FOR MRCS AAUB, CSPF, CQTW AND CTDD: IF REPLY CODE AG IS ENTERED FOR MRC BQDM, REPLY TO MRC AAUB. IF REPLY CODE AX IS ENTERED FOR MRC BQDM, REPLY TO MRCS CSPF AND EITHER CQTW OR CTDD.
BA, BC, BF, BM, BN, BR, BW* #, BX, BY, CG, SA, SB, SC, SE, SK #, SL, SQ, SR, SS, TB, TC (See Note Above)
	AAUB	J	HOLE DIAMETER
	Definition: THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE, AND TERMINATES AT THE CIRCUMFERENCE.
	Reply Instructions: Enter the applicable Reply Codes from Tables 1 and 2 below, followed by the numeric value. (e.g., AAUBJAA0.062; AAUBJLA1.5; AAUBJAB0.047$$JAC0.053*)

Table 1
REPLY CODE	REPLY (AA05)
A	INCHES
L	MILLIMETERS

Table 2
REPLY CODE	REPLY (AC20)
A	NOMINAL
B	MINIMUM
C	MAXIMUM

BA, BC, BF, BM, BN, BR, BW* #, BX, BY, CG, SA, SB, SC, SE, SK #, SL, SQ, SR, SS, TB, TC (See Note Preceding MRC AAUB)
	CSPF	J	HOLE NOMINAL THREAD DIAMETER
	Definition: THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED HOLE, AND TERMINATES AT THE CIRCUMFERENCE.
	Reply Instructions: Enter the applicable Reply Code from the table below, followed by the numeric value. (e.g., CSPFJA0.250; CSPFJL6.0)

REPLY CODE	REPLY (AA05)
A	INCHES
L	MILLIMETERS

	NOTE FOR MRCS CQTW AND CTDD: IF REPLY CODE A IS ENTERED FOR MRC CSPF, REPLY TO MRC CQTW. IF REPLY CODE L IS ENTERED FOR MRC CSPF, REPLY TO MRC CTDD.
BA, BC, BF, BM, BN, BR, BW* #, BX, BY, CG, SA, SB, SC, SE, SK #, SL, SQ, SR, SS, TB, TC (See Note Above and Preceding MRC AAUB)
	CQTW	A	HOLE THREAD QUANTITY PER INCH
	Definition: THE NUMBER OF HOLE THREADS PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
	Reply Instructions: Enter the quantity. (e.g., CQTWA28*)


BA, BC, BF, BM, BN, BR, BW* #, BX, BY, CG, SA, SB, SC, SE, SK #, SL, SQ, SR, SS, TB, TC (See Note Preceding MRCS AAUB and CQTW)
	CTDD	B	HOLE THREAD PITCH IN MILLIMETERS
	Definition: THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE HOLE THREAD AXIS, EXPRESSED IN MILLIMETERS.
	Reply Instructions: Enter the numeric value. (e.g., CTDDB1.0*)

	NOTE FOR MRC CSYM: ENTER REPLY IF NUMERIC VALUE IS LESS THAN 125 MICROINCHES (3.2 MICROMETERS).
BC, BM, BR, BX, CC, SB, SC, SK #, SS, TB, TC* (See Note Above)
	CSYM	J	SURFACE FINISH
	Definition: DESIGNATES THE SPECIFIC SURFACE ROUGHNESS RATING, REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE SURFACE FROM THE MEANLINE IN PROFILE.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code, the applicable Reply Code from the table below and the numeric value. (e.g., CSYM2AXJB32.0; CSYM2AZJB32.0; CSYM2AXJM0.8*)

REPLY CODE	REPLY (AE86)
B	MICROINCHES
M	MICROMETERS

	NOTE FOR MRC CRZS: THE HOLE NEAREST THE HEAD IS CONSIDERED TO BE THE FIRST SHANK HOLE.
	WHEN THE ITEM HAS MORE THAN ONE HOLE AND THE CENTERLINES INTERSECT, ENTER ONE DIMENSION.
BA, BB, BC, BD, BE, BF, BH, BJ, BL, BM, BN, BP, BR, BS, BT, BU, BW, BX, BY, CC, CF, SA, SB, SC, SE, SK, SL, SS, TB, TC, TD*(See Note Above)
	CRZS	J	DISTANCE FROM HEAD LARGEST BEARING SURFACE TO SHANK HOLE CENTER
	Definition: THE DISTANCE FROM THE SHANK HOLE CENTERLINE TO THE LARGEST BEARING SURFACE OF THE HEAD.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code, the applicable Reply Codes from Tables 1 and 2 below, and the numeric value. (e.g., CRZS2AEJAA0.250; CRZS2YAJLA6.0; CRZS2AFJAB0.280$$JAC0.285*)

Table 1
REPLY CODE	REPLY (AA05)
A	INCHES
L	MILLIMETERS

Table 2
REPLY CODE	REPLY (AC20)
A	NOMINAL
B	MINIMUM
C	MAXIMUM

	NOTE FOR MRC AAWB: IF A REPLY IS ENTERED FOR MRC CRZS OR CTWF, REPLY TO MRC AAWB.
BA, BB, BC, BD, BE, BF, BG, BH, BJ, BK, BL, BM, BN, BP, BR, BS, BT, BU, BV, BW, BX, BY, CC, CE, CF, SA, SB, SC, SE, SK, SL, SS, TB, TC, TD* (See Note Above)
	AAWB	J	SHANK UNTHREADED HOLE DIAMETER
	Definition: THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SHANK UNTHREADED HOLE, AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
	Reply Instructions: Enter the applicable I/SAC from Appendix A, Table 2 , followed by the Mode Code, the applicable Reply Codes from Tables 1 and 2 below, and the numeric value. (e.g., AAWB2YAJAA0.047; AAWB2YAJLA1.1; AAWB2AFJAB0.049$$JAC0.058*)

Table 1
REPLY CODE	REPLY (AA05)
A	INCHES
L	MILLIMETERS

Table 2
REPLY CODE	REPLY (AC20)
A	NOMINAL
B	MINIMUM
C	MAXIMUM


ALL*
	UKAS#	D	STRENGTH GRADE DESIGNATION
	Definition: A NUMERIC AND/OR ALPHA-NUMERIC DESIGNATOR WHICH INDICATES THE STRENGTH RATING OF A THREADED FASTENER.
	Reply Instructions: Enter the applicable Reply Code from Appendix A, Table 11 . (e.g., UKASDAB*)


	NOTE FOR MRCS CBBL AND FEAT: FEATURES NOT INCLUDED IN Appendix A, Table 12 ARE TO BE ENTERED IN REPLY TO MRC FEAT.
ALL* (See Note Above)
	CBBL	D	FEATURES PROVIDED
	Definition: THOSE FEATURES, NOT OTHERWISE SPECIFIED, WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
	Reply Instructions: Enter the applicable Reply Code from Appendix A, Table 12 . (e.g., CBBLDAEQ; CBBLDAEQ$$DBBW)


ALL * (See Note Preceding MRC CBBL)
	FEAT	G	SPECIAL FEATURES
	Definition: THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION.
	Reply Instructions: Enter the reply in clear text. Separate multiple replies with a semicolon. (e.g., FEATGADJUSTABLE NOSE CLIP; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE)


ALL*
	TEST	J	TEST DATA DOCUMENT
	Definition: THE SPECIFICATION, STANDARD, DRAWING, OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
	Reply Instructions: Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
	(e.g., TESTJA12345-CWX654321*;
	TESTJA1234A-654321$$JB5556A-663654*;
	TESTJAA2345-654321$JB55566-663654*)

REPLY CODE	REPLY (AC28)
A	SPECIFICATION (Includes engineering type bulletins, brochures, etc., that reflect specification type data in specification format; excludes commercial catalogs, industry directories, and similar trade publications, reflecting general type data on certain environmental and performance requirements and test conditions that are shown as "typical," "average," "nominal," etc.)
B	STANDARD (Includes industry or association standards, individual manufacturer standards, etc.)
C	DRAWING (This is the basic governing drawing, such as a contractor drawing, original equipment manufacturer drawing, etc.; excludes any specification, standard, or other document that may be referenced in a basic governing drawing)

ALL*
	SPCL	G	SPECIAL TEST FEATURES
	Definition: TEST CONDITIONS AND RATINGS, OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
	Reply Instructions: Enter the reply in clear text. (e.g., SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)


ALL *
	ZZZK*	J	SPECIFICATION/STANDARD DATA
	Definition: THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
	Reply Instructions: Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
	(e.g., ZZZKJT81337-30642B*;
	ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;
	ZZZKJP80205-NAS1103*;
	ZZZKJS81349-MIL-C-1140C/CE/*;
	ZZZKJT81337-30642B$$JP80205-NAS1103*)

REPLY CODE	REPLY (AN62)
S	GOVERNMENT SPECIFICATION
T	GOVERNMENT STANDARD
D	MANUFACTURERS SOURCE CONTROL
R	MANUFACTURERS SPECIFICATION
N	MANUFACTURERS SPECIFICATION CONTROL
M	MANUFACTURERS STANDARD
B	NATIONAL STD/SPEC
A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

	NOTE FOR MRC ZZZT: IF THE SPECIFICATION/STANDARD CITED IN REPLY TO MRC ZZZK IS NONDEFINITIVE, REPLY TO MRC ZZZT. THIS REPLY IS THE DATA WHICH IS NOT RECORDED IN SEGMENT C.
ALL* (See Note Above)
	ZZZT	J	NONDEFINITIVE SPEC/STD DATA
	Definition: THE NUMBER, LETTER, OR SYMBOL THAT INDICATES THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE, OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
	Reply Instructions: Enter the applicable Reply Code from Appendix A, Table 13 , followed by the appropriate number, letter, or symbol. (e.g., ZZZTJTY1; ZZZTJTY1$$JSTA; ZZZTJTY1$JSTA*)


ALL*
	ZZZW	G	DEPARTURE FROM CITED DOCUMENT
	Definition: THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY WHICH DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL, OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS, OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
	Reply Instructions: Enter the reply in clear text. (e.g., ZZZWGAS MODIFIED BY MATERIAL*)


ALL*
	ZZZX	G	DEPARTURE FROM CITED DESIGNATOR
	Definition: THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
	Reply Instructions: Enter the reply in clear text. (e.g., ZZZXGAS MODIFIED BY MATERIAL*)


ALL*
	ZZZY	G	REFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
	Definition: A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
	Reply Instructions: Enter the reply in clear text. (e.g., ZZZYGCOLOR CODED LEADS; ZZZYGAS DIFFERENTIATED BY MATERIAL)


ALL*
	CRTL	A	CRITICALITY CODE JUSTIFICATION
	Definition: THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE, FIT, PERFORMANCE, OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
	Reply Instructions: Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical. (e.g., CRTLAMATL; CRTLAMATL$$ASURF)
	Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.


	NOTE FOR MRC PRPY: IF DOCUMENT AVAILABILITY CODE B, D, F, OR H, REPLY TO MRC PRPY.
ALL* (See Note Above)
	PRPY	A	PROPRIETARY CHARACTERISTICS
	Definition: IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
	Reply Instructions: Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using AND coding ($$) for multiple characteristics. If all the MRCs are proprietary, enter the reply PACS. If none of the MRCs is proprietary, enter the reply NPAC. (e.g., PRPYAPACS; PRPYANPAC; PRPYAMATL$$ASURF*)


ALL*
	ELRN	G	EXTRA LONG REFERENCE NUMBER
	Definition: A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
	Reply Instructions: Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code. (e.g., ELRNGANN112036BIL060557LEN0313605UZ062365*)
	In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.


	NOTE FOR MRC NHCF: IF THE CRITICALITY CODE IS E, H, OR M, REPLY TO MRC NHCF.
ALL* (See Note Above)
	NHCF	D	NUCLEAR HARDNESS CRITICAL FEATURE
	Definition: AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
	Reply Instructions: Enter the Reply Code from the table below. (e.g., NHCFDCY*)

REPLY CODE	REPLY (AD05)
CY	HARDENED

ALL*
	ELCD	D	EXTRA LONG CHARACTERISTIC DESCRIPTION
	Definition: A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
	Reply Instructions: Enter the Reply Code from the table below. (e.g., ELCDDA*)

REPLY CODE	REPLY (AN58)
A	ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD

ALL*
	ANMM#	D	THREAD FORMING METHOD
	Definition: THE MEANS USED IN FORMING THE THREAD.
	Reply Instructions: Enter the applicable Reply Code from the table below. (e.g., ANMMDAS*)

REPLY CODE	REPLY (AA62)
AH	CUT
AS	ROLLED

ALL*
	AARN#	D	FABRICATION METHOD
	Definition: THE PROCESS USED IN MANUFACTURING THE ITEM.
	Reply Instructions: Enter the applicable Reply Code from the table below. (e.g., AARNDAJ*)

REPLY CODE	REPLY (AA62)
AN	CAST
AJ	FORGED
AZ	MACHINED

ALL*
	FRAA#	G	AUXILIARY PARTS
	Definition: SUCH PARTS AS NUTS, WASHERS, PINS, AND THE LIKE, WHICH ARE COMPONENTS OF THE ITEM OF SUPPLY AND ARE INTENDED TO BE USED WITH THE MAIN COMPONENT ITEM.
	Reply Instructions: Enter the name, Standardization symbol, material and surface treatment in clear text separated with dashes.
	(e.g., FRAAGNUT-HK-XC38-CADMIUM*)
	Separate multiple replies with a semicolon.
	(e.g., FRAAGNUT-HK-XC38-CADMIUM; PIN-U-A33-CADMIUM; WASHER-Z-A52-CADMIUM*)


ALL*
	PRMT	D	PRECIOUS MATERIAL
	Definition: IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
	Reply Instructions: Enter the applicable Reply Code from Appendix A, Table 14 . (e.g., PRMTDAUA000; PRMTDAUA000$$DAGA000; PRMTDAGA000$DAUA000*)


ALL*
	PMWT	J	PRECIOUS MATERIAL AND WEIGHT
	Definition: AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM, AND THE AMOUNT PER A MEASUREMENT SCALE.
	Reply Instructions: Enter the applicable Reply Code from Appendix A, Table 14 and the table below, followed by the numeric value. (e.g., PMWTJAUA000F1.000; PMWTJAUA000F0.500$$JAGA000R0.780)

REPLY CODE	REPLY (AG14)
E	GRAINS, TROY
R	GRAMS
F	OUNCES, TROY

ALL*
	PMLC	J	PRECIOUS MATERIAL AND LOCATION
	Definition: AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
	Reply Instructions: Enter the applicable Reply Code from Appendix A, Table 14 , followed by the location in clear text. (e.g., PMLCJAGA000OVERALL; PMLCJAUA000THREADS$$JAGA000HEAD; PMLCJAUA000THREADS$JAGA000THREADS*)

ALL*
	SUPP	G	SUPPLEMENTARY FEATURES
	Definition: CHARACTERISTICS OR QUALITIES OF AN ITEM, NOT COVERED IN ANY OTHER REQUIREMENT, WHICH ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS EXCLUDING NSN ASSIGNMENT.
	Reply Instructions: Enter the reply in clear text. (e.g., SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT*)


	NOTE FOR MRC ENAC: ANSWERING THIS MRC WILL GENERATE AN ENAC CODE IN THE ITEM IDENTIFICATION SEGMENT (A) OF THE NSN.
ALL* (See Note Above)
	ENAC	D	ENVIRONMENTAL ATTRIBUTE CODE
	Definition: INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
	Reply Instructions: Enter the applicable Reply Code from the table below. (e.g., ENACDAK*)

REPLY CODE	REPLY (EN02)
AK	NON-CADMIUM ALTERNATIVE PRODUCT

ALL*
	ZZZP	J	PURCHASE DESCRIPTION IDENTIFICATION
	Definition: THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
	Reply Instructions: Enter the 5-position Commercial and Government Entity (CAGE) Code, followed by a dash and the identifying number of the document.
	(e.g.,ZZZPJ81A37-30624A*)


ALL*
	AGAV	G	END ITEM IDENTIFICATION
	Definition: THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
	Reply Instructions: Enter the reply in clear text.
	(e.g., AGAVG3930-00-000-0000*;
	AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)


ALL*
	ZZZV	G	FSC APPLICATION DATA
	Definition: THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS (FSC) TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
	Reply Instructions: Enter the name of the next higher classifiable assembly in clear text. (e.g., ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)


ALL *
	CXCY	G	PART NAME ASSIGNED BY CONTROLLING AGENCY
	Definition: THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
	Reply Instructions: Enter the reply in clear text. (e.g., CXCYGLINE PROCESSOR CONTROL BOARD*)


ALL*
	HZRD	D	HAZARDOUS SUBSTANCES
	Definition: THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
	Reply Instructions: Enter the applicable Reply Code from the table below. (e.g., HZRDDHAZ008*; HZRDDHAZ011$$DHAZ012)

REPLY CODE	REPLY (HZ00)
HAZ008	CADMIUM
HAZ011	CHROMIUM
HAZ012	COPPER
HAZ027	IRIDIUM
HAZ222	IRON
HAZ029	LEAD
HAZ092	MAGNESIUM
HAZ030	MAGNESIUM ALLOY
HAZ252	NICKEL
HAZ285	PLASTIC
HAZ286	PLATINUM
HAZ303	SILVER